Skip to content
How To Make a Gravity Bong: Step-by-Step Guide
Are you looking for a new way to enjoy cannabis? Gravity bongs can offer a potent experience. This guide walks you through making and using your own gravity bong at home, easily and quickly.
Get ready to learn!
Key Takeaways
- To make a gravity bong, you need a plastic bottle, a larger container for water, aluminum foil, tape or rubber bands, scissors or a knife, and cannabis.
- Prepare the bong by cutting off the bottom of the plastic bottle and making a bowl out of aluminum foil to hold the cannabis. Submerge the cut bottle in water to create a seal.
- Light your smoking material and slowly lift the bottle to fill it with smoke. Then inhale by removing the bowl cap and pushing down on the bottle.
- To use your gravity bong properly, light the bowl evenly and pull up on the bottle gently. Take care not to let water inside it.
- After using, disassemble and clean each part of your bong with warm water to keep it ready for next time.
How to Make a Gravity Bong in 10 Minutes
Make a gravity bong in just 10 minutes. Gather supplies, prepare plastic bottle, and assemble the bong.
Gather supplies
Start by collecting all necessary items for your homemade gravity bong. You'll need a plastic bottle, a larger container like a bucket or a second, bigger plastic bottle cut in half to hold water, some aluminum foil, tape or rubber bands, and something sharp like scissors or a knife.
Don't forget your smoking material - cannabis.
Next, ensure the cap of the smaller plastic bottle fits tightly; this will keep everything secure during use. With these supplies ready, you're set to build an effective DIY gravity bong at home.
This simple setup uses items you likely have lying around, turning them into a functional smoking device without much hassle.
Prepare plastic bottle
To prepare the plastic bottle, carefully cut off the bottom using a sharp knife or scissors. Make sure to discard the cap before cutting, leaving just the top portion of the bottle.
Then, fill a container with water and submerge the cut end of the bottle into it. This will create a seal for your gravity bong system.
Next, fashion a bowl from aluminum foil by molding it over the top of a pen or similar object and poking small holes in it which will allow airflow. Screw this makeshift bowl onto the capless end of your plastic bottle to complete its assembly as part of making your homemade geeb.
Assemble the bong
Assembling the bong is simple. First, cut the bottom off a plastic bottle. Next, cover the mouth of the bottle with aluminum foil and poke small holes in it. Then, fill a bucket or large container with water.
Place the bottle into the water without letting any water inside it. Put your smoking substance on the aluminum foil and light it while slowly pulling up on the bottle to draw smoke in.
Finally, remove the foil cap and inhale to enjoy.
How to Use a Gravity Bong
To inhale, light the bowl and slowly pull up on the bottle to fill it with smoke. Then, remove the bowl and push the bottle back down while breathing in to take a hit.
Lighting the bowl
To light the bowl, hold a lighter over the cannabis while inhaling slowly. Ensure the flame touches the green herb to ignite it evenly. Wait for the entire surface area of the herb to cherry before removing the flame.
Rotate and stir gently if necessary to promote even burning.
Inhaling and taking a hit
To inhale, place your mouth on the opening of the bottle. Light the bowl and slowly pull up on the plastic bag to fill it with smoke. Once filled, unscrew the cap and push down while inhaling to draw in all the smoke.
Hold your breath briefly before exhaling for a potent hit.
When taking a hit, ensure you control how much smoke you inhale to avoid harshness. Adjust your inhalation speed based on your tolerance and preferences.
Disassembling the bong
To disassemble the bong, carefully unscrew or remove any detachable parts. Gently rinse each piece with warm water to clean out any residue. Pat them dry with a clean towel or let them air dry before storing them properly in a safe place.
Dispose of the water and thoroughly clean the bottle or receptacle used for your gravity bong to prevent odors and buildup. Store all supplies securely so they are ready for your next session.
Conclusion
Crafting a gravity bong is an easy and fun DIY project. Once you have gathered your supplies, follow the step-by-step guide to assemble and disassemble the bong in just 10 minutes.
Now that you know how it's done, go ahead and give it a try for an alternative smoking experience. Enjoy!
FAQs
1. What is a gravity bong?
A gravity bong is a homemade smoking tool that uses water and air pressure to create smoke from cannabis.
2. How do you make a homemade gravity bong?
To make a homemade gravity bong, you need a plastic bottle and water pipe setup. You cut the bottle and use it with water to pull smoke through the contraption.
3. Can anyone create a geeb at home?
Yes, anyone can craft a geeb or gravity bong at home by following simple step-by-step guides using everyday items like plastic bottles for an alternative smoking method.
4. Are there any tips for making my first gravity bong work well?
For your first DIY smoking device, ensure tight seals where needed and follow crafting tips closely to enjoy your cannabis consumption safely.
5. What are the benefits of using a gravity bong compared to other methods?
Using a gravity bong allows for efficient marijuana smoke production with minimal materials, offering an intense experience different from traditional smoking apparatuses.
